BondKote
High Performance Epoxy Mastic Filler & Bonding Agent
BondKote is a 100% solids, extremely low VOCs, fast curing, technologically advanced epoxy mastic and filler developed with SafeResin technology.
This mastic product has been specifically formulated to meet the requirements as a high performance filler and bonding agent. BondKote provides excellent adhesion and fills in project holes and divots providing a smooth surface to coat over.
$469.00
SKU: 42001
Select quantity
NOTE: 1 unit (3 gallons) of parts a/b mixed covers 400 to 500 sq./ft.
Welcome to the next level of coating innovation.
When we set out to advance epoxy resin technology, we knew we had to start at the foundation. So we looked at the chemistry behind the material and discovered ways in which it could be improved. The result—SafeResin™. Safer, Stronger, Faster, and Easier. The resin technology that is anything but ordinary.
Key Attributes
- All-purpose bond agent, grout & filler
- Cures in moist environments
- Maximum bond strength
- Ultra Low VOCs and no foul odors
- LOW ENVIRONMENTAL IMPACT
- Fully cured 24-48 hours ( at 70°F)
- Super charged by SafeResin technology
KoreKote BondKote
Technical
Data Sheet
DOWNLOAD
Recommended Substrates
- Concrete
- Stone
- Masonry
- Steel
- Stainless Steel
- Wood Decking
- Plywood
- Pressboard
- abs plastic
- pvc plastic
- polycarbonate plastic
Coverage Guide
1 unit (3 gallons) of parts a/b mixed covers 400 to 500 sq./ft.
BondKote
MASTIC & FILLER EPOXY COATING
Surface Preparation
Cleaning
clean surfaces to remove all dust, dirt and grease. For highest bond strength, chemical cleaning is required. We recommended useing KoreKote Surface Cleaner@
Mixing
Mix 2:1 ratio by volume of Part A (resin) and Part B (hardener) together. Mix thoroughly until uniform color and consistency throughout. Mechanical Stir Stick (drill with mixing paddle) is recommended.
Potlife
Potlife of mixed coating is approximately 20 minutes at 70˚F if material is left as a unit in mixing container. Higher temperatures reduce potlife and accelerate curing.
CAUTION:Mixing large quantities (more than a 3 gallon batch size) generates significant heat and shortens potlife.
Application
Begin by pouring mixed material in a straight line 2 – 3 feet from the desired starting edge of the area being coated. Use lint free 3/8” nap roller on roller frame and spread material evenly over surface. Use brush to do cut-ins along edges and corners if necessary. When material is spread out in a thinner layer, the worklife is extended to approximately 35 minutes (do not apply in temperatures below 50°F).
Curing
Allow coating to cure at 50˚F or higher.
Curing profile at 70°F
- Gel time: 40 minutes
- Crystallized: 4 hours
- Extra strong 40ml coating (Two Coats)
- Cured: 24 – 48 hours (depending on temperature and application)
Clean Up
Use denatured alcohol (not necessary to use harmful/toxic solvents) to cleanup uncured material and tools.
Safty
Precautions
Avoid contact with eyes and / or skin. Wash thoroughly after handling. Provide adequate ventilation to control vapor. KEEP OUT OF THE REACH OF CHILDREN.
SUGGESTED FIRST AID
IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. Call a POISON CONTROL CENTER if you feel unwell.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice. Immediately call a doctor.
IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. Wash contaminated clothing before reuse. If skin irritation or rash occurs: Get medical attention.
IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call a doctor.
HANDLING SAFETY
Prolonged exposure to Part A (resin) may cause allergic skin reaction on sensitive skin and possible respiratory tract irritation. Prolonged exposure to Part B (hardener) may cause an allergic skin reaction on sensitive skin..